100pcs CN-ZF Ceramic Tile Leveler +200pcs Cross

100pcs CN-ZF Ceramic Tile Leveler +200pcs Cross Spacers(1/16” and 5/64”) in Total for Floor and Wall Construction Tools, Reusable Tile Leveling
- HARDNESS: The plastic part of the Tile Leveler is made of POM (polyacetal POM) which features hardness in extreme extent as compared with other product’s using PP materials. This effectively avoids deformation and fracture of the product.The T-needle is made of high quality round stainless steel. The design is galvanized, wear resistant and corrosion resistant.
- LATEST UPGRADED: The most recent upgraded Tile Leveler with the minimum spacing reduced to 1.5mm(1/16") after laying。you can make the laying gap smaller and more beautiful.
- EASY TO USE and EFFICIENT:These Tile Leveling System Suitable for DIY operation and it can be reused. About 100 pieces can be laid with 30 tiles;These Tile Leveling System Raised the efficiency of ceramic tile installation significantly. Make ceramic tile flat in perfect appearance;
- GOOD APPLICABILITY:These Tile Leveling System Suitable for tile thickness between 3mm(1/8 in) - 15mm(19/32 in);
- OUR PROMISE: We will always provide you with quality products and good service, if you don't like it, we promise to replace the product or unconditional refund. We welcome you to contact us at any time, we will provide you with a satisfactory solution.
What will you get:
1.100 pcs tile Leveler +2 pcs special spanner
2.100pcs(2.0mm)ï¼ˆ5/64")+ 100pcs(1.5mm)(1/16"ï¼‰ cross spacer
Usage:
-Paving the first tile, leave more than 1.5mm (use with cross spacer). Close to the tiles.
-Insert T-shaped needle along the gap in the tile.
-Then rotate 90 degrees so that the T-needle is stuck at the bottom of the two tiles and rotate slightly left and right to make some space
-Adjust the caps with your hand/special wrench until the two tiles are on the same level.
-About 2-5 hours after leveling, before cement/adhesive is completely dry, rotate caps in the reverse direction and remove the T-needles.
Make the following three steps in advance to avoid being unable to take out the t-type leveler for reuse:
1. Tile slitting 1.5mm or above, preferably use with cross card;
2. Clean up the cement and debris around the T-needle before installation;
3.The T-needles should be removed 2-5 hours after installed and before the cement/adhesive is completely solidified. However, depending on the climate and environmental conditions, the drying time will be different. The user can properly grasp the dismantling time according to the actual situation or carefully refer to the cement/adhesive instruction manual.
Tip:
1ã€When the T-needle is stuck in the bottom of the two tiles, shake it slightly from side to side to make some room for easier removal and reuse.
2ã€ When laying the tiles with length more than 80CM (31.5 inches), the distance between two T-needles shall be kept less than 60CM (23 inches), or add one more T-needle in this side.
3ã€When the cement layer or adhesive thinset is less than 3mm, this product is not suitable for useï¼
Specification:
Material: POM (polyacetal POM) + 430 Stainless Steel
Quantity: 100 Sets/Bag + 2Pcs Tool
Suitable Space: 1.5mm(1/16 in)-3mm(1/8 in) Space
Tile thickness: 3mm(1/8 in) -15mm(19/32 in)
Color: As showed in the picture
Country USA
Brand CN-ZF
Manufacturer huizhoushizhifu
Binding Tools & Home Improvement
ItemPartNumber large -100
Model large -100
Color Yellow Large
Size 100pcs
UPCs 753318733510
EANs 0753318733510
ReleaseDate 0000-00-00

Country	USA
Brand	CN-ZF
Manufacturer	huizhoushizhifu
Binding	Tools & Home Improvement
ItemPartNumber	large -100
Model	large -100
Color	Yellow Large
Size	100pcs
UPCs	753318733510
EANs	0753318733510
ReleaseDate	0000-00-00

100pcs CN-ZF Ceramic Tile Leveler +200pcs Cross Spacers(1/16” and 5/64”) in Total for Floor and Wall Construction Tools, Reusable Tile Leveling