ABN Air Compressor Clutch Rebuild Removal Tool Kit AC Clutch

ABN Air Compressor Clutch Rebuild Removal Tool Kit AC Clutch Puller for Car Auto Air Conditioning on GM, Ford, Chrysler
- REPLACE A/C CLUTCH ASSEMBLY: Use the ABN Air Compressor Clutch Rebuild Removal Tool Kit – AC Clutch Puller for Car Auto Air Conditioning to remove, install, or rebuild clutches found on FS6, C171, 6P, and 148 compressors; GM R4 and A6, HR-6, DA-6 and V A/C compressors; sander compressors SD 505, 507, 575, 708, and 709; Wide application of vehicles including GM, Ford, Chrysler, imports, and other makes and models; Check vehicle owner’s manual for a list of compatible compressors
- EASY TO USE: Keep all threads clean and well-oiled; Outer part of tool has smooth side and threaded side (threads used to attach to inner clutch shaft when removing); Start with one bearing between tool and clutch, and thread down fully onto compressor's inner shaft threads (This is the fixed part - inner bolt does not move when threading down outer piece); Remove tool and stack other bearing on to take up the distance the clutch pushed into pulley
- BUILT TO LAST: Constructed from stainless steel with a black coated finish for ultimate strength and longevity; Resists rust and corrosion with proper care and lubrication; 2 and 3 hold puller plate allows mechanical force to do all of the pulling on most clutches
- EASY STORAGE: Heavy-duty 10.5” x 8.25” x 2.25” inch (26.7cm x 21cm x 5.7cm) plastic blow-molded carrying case with handle for easy transport, safe storage, and quick organization
- CONTENTS: Complete with puller body, jaw and sleeve assembly, jack-screw, thrust washer, button, bearing, and puller plates; includes (1) 3-eye round clutch plate sander arbor, (3) 1/4-inch – 20 Hex screws, (2) 3/8-inch – 16 Hex screws, (1) Sander arbor drive bolt, (1) Chrysler, Denso, Ford metric hub arbor remover, (1) GM standard thread clutch hub arbor remover / installer, (1) GM metric thread clutch hub arbor remover / installer, (1) arbor remover bearing, and (1) carrying case
If your vehicle's compressor or compressor clutch does not cool or cools poorly, is loud and noisy, or even seizes up, it is time to for a replacement. Sometimes the clutch assembly can be very difficult to remove from the compressor, but the ABN Air Compressor Clutch Rebuild Removal Tool Kit - AC Clutch Puller for Car Auto Air Conditioning GM, Ford, Chrysler cuts down on removal time on any R&R job. You can remove, install, or rebuild clutches found on FS6, C171, 6P, and 148 compressors, GM R4 and A6, HR-6, DA-6 and V A/C compressors, sander compressors SD 505, 507, 575, 708, and 709. Each piece is constructed from stainless steel with a black coated finish for strength and to resist rust and corrosion with proper care and lubrication. Pulley/clutch holder and 3-jaw puller not included. WARNING: This product can expose you to chemicals which is [are] known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Country USA
Brand ABN
Manufacturer ABN
Binding Misc.
ItemPartNumber 9916
Model ABN-9916
UPCs 688295879916
EANs 0688295879916
ReleaseDate 0000-00-00

Country	USA
Brand	ABN
Manufacturer	ABN
Binding	Misc.
ItemPartNumber	9916
Model	ABN-9916
UPCs	688295879916
EANs	0688295879916
ReleaseDate	0000-00-00

ABN Air Compressor Clutch Rebuild Removal Tool Kit AC Clutch Puller for Car Auto Air Conditioning on GM, Ford, Chrysler

You might also like...