Alightings LED Connector 5 Pin for 12mm RGBW Waterproof LED

Alightings LED Connector 5 Pin for 12mm RGBW Waterproof LED Strip Lights- Strip to Wire Quick Connection, 20 - 18 AWG Wire No Stripping
- Reminder: Pls distinguish carefully the specifications of your strip light before placing order. If it is 10mm wide PCB，RGB or Non-waterproof Ribbon Light, please do not buy this connector.
- These led connector suitable for 5 pin 12mm 5050 STANDARD WATERPROOF LED strip lights(PU surface,not Silicone surface), One end for 5 core extension wire and another end for RGBW waterproof strip light. Suggest refer to updated version.(ASIN:B09L7XSTL8)
- If your RGBW strip are NON-WATERPROOF or NON-STANDARD WATERPROOF lights(too soft or too thin ), pls use this item (ASIN:B09L7XSTL8)
- Suggest match standard 20awg extension cable, pls refer to ASIN: B07CVSJ3DP . without stripping wire, no soldering, connect the 5 core extension wire to get lighting exactly where you want it.
- Firmly bite through the strip, don’t like traditional connector only conductive connection, it is a solid connection and much stronger
NOTE: 1.Make sure your section of LED light strip is 12MM wide 5PIN STANDARD WATERPROOF LED Strip Light(PU surface,not Silicone surface).
2.If your RGBW strip are NON-WATERPROOF or NON-STANDARD WATERPROOF lights(too soft or too thin), pls use this item (ASIN:B06XHCMLVB)

Solderless Wire Joint Quick Splice Connector for 20-18awg Cable
Our products were an innovative safe and quick wire connector,peeling free,tapping free and twisting free. well waterproof and dust proof function. it greatly changes the way of wire connection .it allow any users to just insert the wire into wire joint and press cover by pliers to connect the wire safely and conveniently.

Firmly bite the strip, no need to peel back the silicon cover
Updated version of LED strip connectors, assemble wire by yourself as needed, flexible to different project! No need to solder. Just clasp your prepared led strip section into the connector to get connected. Connect waterproof LED strip without removing surface coating silicon gel, compatible with 30-60 LEDs/M strip, made of flame retardant material, safely use. Support high current LED strip lights.

Installation Instructions:
Strip End:
1.Open the transparent cover of connector up to 90 degrees.
2.Peel off the 3M glue from the back of the strip light.
3.Insert the strip section to the end of strip side of connector, keep the silicone surface face up.
4.Close the transparent cap with a plier until it is fully seated on both sides of the bottom base.
Wire End:
1.Cut the desired wire length and insert it directly into the guide slot.
2.Make sure that the positive & negative on the strip light surface are corresponding to the ones on the wires.
3.Close the transparent cap with a plier until it is fully seated on both sides of the bottom base.
4. End of installation.

Package:
10pcs Strip to Wire Connectors (AC-DJ-N12XB-5)
Country USA
Brand Alightings
Manufacturer Alightings
Binding Kitchen
ItemPartNumber SYNCHKG121470
Model SYNCHKG121470
Color for RGBW Waterproof
UPCs 647336181128
EANs 0653472988392
ReleaseDate 0000-00-00

Country	USA
Brand	Alightings
Manufacturer	Alightings
Binding	Kitchen
ItemPartNumber	SYNCHKG121470
Model	SYNCHKG121470
Color	for RGBW Waterproof
UPCs	647336181128
EANs	0653472988392
ReleaseDate	0000-00-00

Alightings LED Connector 5 Pin for 12mm RGBW Waterproof LED Strip Lights- Strip to Wire Quick Connection, 20 - 18 AWG Wire No Stripping

You might also like...