IMPRESA Brewer Needle Cleaning Tool/Maintenance Accessory -

IMPRESA Brewer Needle Cleaning Tool/Maintenance Accessory - Compatible With Keurig 2.0 - No More Grounds In Your Coffee or Partial Brews
- No More Partial Brews Or Grounds In Your Coffee: Are you getting partial / interrupted brews, grounds in your coffee, or a "water under pressure" message? There's a good chance you have a clogged entrance / exit needle caused by a natural build-up of coffee grounds. Our tool helps remove those grounds and gets your Keurig (R) brewer running smoothly again
- Lengthens The Life Of Your Machine: Our needle cleaning accessory is a key aspect of your brewer maintenance, along with regular cleaning and descaling. A clogged needle, if left untreated for too long, can lead your machine to break down. Don't let that happen - regularly clean your brewing needle!
- Compatible With Keurig (R) 2.0: Compatible with all Keurig (R) 2.0 and Plus Series brewers / coffee makers / coffeemakers, including model #s K200, K250, K300, K350, K375, K400, K450, K460, K475, K500, K550, K560, K575, K600, K650, K660, K675. This will Not work with K55 Machine or K-Elite.
- Easy To Use: In just a few minutes you'll be back up and running! Instructions below. Note: Will not work with non-Keurig (R) brewers or other Keurig (R) models not listed
- Please note: This is an aftermarket replacement product (produced by Impresa Products). We have no affiliation with or endorsement from any of the manufacturers mentioned
BACKED BY OUR TOP-RATED WARRANTY AND CUSTOMER SERVICE!

No more partial brews or grounds in your coffee
Lengthens the life of your machine
Compatible with Keurig (R) 2.0
Easy to use

INSTRUCTIONS FOR USE: 1) Ensure that your brewer is powered off. 2) Ensure that the silicone chamber is seated in the plastic holder with the entrance facing up. 3) Entirely fill the silicone chamber with warm water. 4) Lift the handle (where you would normally place a pod) and place the cleaning tool in the pod holder. 5) Ensure that the cleaning tool is fully seated and flush with the pod holder. If it is not fitting in, adjust until it fits smoothly. 6) Raise and lower the handle 5 times, each (5 ups and 5 downs). This will flush water through the needle to remove the coffee grounds. 7) Remove the cleaning tool from the pod holder. You will see collected coffee grounds. 8) Perform a cleansing brew, ensuring that there is a mug on the drip tray. NOTE: Ensure that the pod slot is empty during the cleaning brew. Some models may require you to hold down the brew button (to brew 6 ounces of hot water). 9) Once the brew is complete, pour the contents of the mug into the sink. Rinse the cleaning tool with warm water and allow to fully air dry. This is a generic product manufactured and distributed by Impresa Products (TM). This is not a Keurig (R) OEM product and Impresa Products has no affiliation with or endorsement from Keurig (R). Our product is not covered under any Keurig (R) manufacturer's warranty. The Keurig (R) brand names and logos are the registered trademarks of their owners. Any use of the Keurig (R) brand names, models or any other related designations are made solely for purposes of describing and illustrating compatibility. Does not work with K-Elite or K-55 Machines
Country USA
Brand IMPRESA
Manufacturer IMPRESA
Binding Kitchen
ItemPartNumber 8541892894
Model 8541892894
Color Black
Size 1 Count (Pack of 1)
UnitCount 1
UPCs 850523008706
EANs 0850523008706
ReleaseDate 0000-00-00

Country	USA
Brand	IMPRESA
Manufacturer	IMPRESA
Binding	Kitchen
ItemPartNumber	8541892894
Model	8541892894
Color	Black
Size	1 Count (Pack of 1)
UnitCount	1
UPCs	850523008706
EANs	0850523008706
ReleaseDate	0000-00-00

IMPRESA Brewer Needle Cleaning Tool/Maintenance Accessory - Compatible With Keurig 2.0 - No More Grounds In Your Coffee or Partial Brews

You might also like...