DROK DC Buck Module, Adjustable Buck Converter Step Down

DROK DC Buck Module, Adjustable Buck Converter Step Down Voltage Regulator 6V-32V 30V 24V 12V to 1.5-32V 5V 5A LCD Power Supply Volt Reducer Transformer Module Board with USB Port Protective Case
- PARAMETER --- Input voltage range DC 6V-32V; Output voltage DC 1.5V-32V; Max output current 5A, recommend use of within 4.5A; Max output power 75W, recommend use of within 50W.
- GENERAL USE --- As ordinary step-down module with over-current protection; As constant current LED driver module; DIY a solar power controller, etc.
- DISPLAY --- Large clear digital LCD display voltage & current value simultaneously.
- FEATURES --- Constant current/voltage mode; Voltage calibration & current calibration; USB interface; Protective case; Short-circuit protection; Over-temperature protection; Input reverse connection protection.
- NOTE --- 1). Output voltage is set as around 20V by default, if your input is lower than that, please turn potentiometer anticlockwise for 10 laps or more until voltage changes. 2). The case is packaged unassembled to avoid damage during transit. It needs to be manually installed. 3). Please carefully read the user’s manual, especially the “Cautions” before using. You can find the PDF Instructions on this page -- Product information -- Product guides and documents -- User Manual [PDF].
Parametersï¼š
Chip: MP2304
Input voltage: 6~32V
Output voltage: 1.5~32V continuously adjustable (Input should be 1.5V higher than output.)
Output current: 5A max, adjustable, recommended use within 4.5A. (Over 3A or 35W, please enhance heat dissipation.) Constant current requires an output voltage of above 2V to be adjusted. Current regulation can only be performed in the status of constant current.
Output Power: 75W (max), recommended use within 50W. Please reduce the power when voltage difference is large.
Operating temperature: -20â„ƒ to +70â„ƒ
Operating frequency: 180KHz
Conversion efficiency: up to 96%
Short circuit protection: Yes (Constant current value set by constant current function)
Over-temperature protection: Yes (Automatically shut off the output when overtemp.)
Input reverse polarity protection: Yes
Output backflow prevention: None. Please add a diode when used for charging.
Installation: 8x pillars, 8x 3mm screws
Wire Connection: terminal block or soldering terminals; VIN is input; VOUT is output.
Dimension: 65.6*40*25mm

Display Modes:
1). F-0 mode: Display output voltage
2). F-1 mode: Display input voltage
3). F-2 mode: Display input and output voltage alternately
4). USB mode: Display USB output voltage & turn on/off USB output

Note:
Output is set as around 20V before leaving factory, if your input is lower than that, please turn potentiometer anticlockwise for at least 10 laps until voltage changes.

Package Included:
1x DC Buck Module
4x Copper Cylinder Screws M3*6
4x Double-pass Screws M3*12
8x Roundhead Screws M3*6
Country USA
Brand DROK
Manufacturer DROK
Binding Misc.
ItemPartNumber 180080AFA
Model 180080AFA
Color clear black
Size Buck 6-32V to 1.5-32V
ReleaseDate 0000-00-00

Country	USA
Brand	DROK
Manufacturer	DROK
Binding	Misc.
ItemPartNumber	180080AFA
Model	180080AFA
Color	clear black
Size	Buck 6-32V to 1.5-32V
ReleaseDate	0000-00-00

DROK DC Buck Module, Adjustable Buck Converter Step Down Voltage Regulator 6V-32V 30V 24V 12V to 1.5-32V 5V 5A LCD Power Supply Volt Reducer Transformer Module Board with USB Port Protective Case

You might also like...