Dash Cam Hardwire Kit Micro USB 10ft 12V-24V to 5V, Low

Dash Cam Hardwire Kit Micro USB 10ft 12V-24V to 5V, Low Voltage Protection Mini/ACS/ATO Add a Circuit Fuse Holders Compatible Dash Cam, GPS, Radar Detector All Other Micro USB Device
- 【Compatible 12 – 24V Vehicles】This hardwire kit dash cam connects the camera directly to the car, truck, bus, SUVs, or big rig for continuous power, accepts voltage from any type of vehicles runs on 12 – 24V.
- 【ENOUGH LENGTH】Overall 10ft hardwire kit can be installed basically on All vehicles. Input length: 3ft, Output length: 7ft.
- 【Power Supply】Directly to the ignition wire for power only so it can turn on and off with the ignition and you don't have to worry about plugging in the charger, or turning the dashcam on, or any such stuff.
- 【Low voltage protection】It has a smart low voltage protection system that will automatically shut off the power to your dash cam when the battery voltage drops to 11.4V or 22.8V, thus preventing it from draining the battery.
- 【Mulitiple uses】Mini USB plug compatible with all mini USB dash cams such as Rexing, ROAV, Anker, Aukey. GPS navigator and radar detector etc, it always frees up the cigarette lighter for other devices.
Key Features
Compatible with 12-24Vdc for car or truck installations.
Perfect for 24/7 Parking Surveillance.
Low voltage protection protects against battery dying.
Works well with Rexing, ROAV, Anker, Aukey and all the other mini usb dash cams!
Keep 12V or 24V outlet free, charge your phone at the same time.
Installation Instruction
Find the Correct Fuse Slot
Open the fuse box, find the correct fuse slot for your hardwire kit. If you need to find an ignition switched fuse, put the key in the vehicle, find the fuse which is not lit up while the car is off, and test it by turning the car on to see if it lights up. If your kit requires constant power, turn off the car and remove the key to see which fuse slots stays lit on.
Connect the Red Wire
Once you've determined which fuse slots you need to use for your hardwiring kit you can crimp the red wire of your hardwire kit onto the Add-A-Fuse. Gently remove the fuse you identified. Install the fuse you just removed into the installation kit add-a-fuse circuit. Plug the add-a-circuit into the fuse box in the correct orientation.
Ground the Hardwiring Kit
Slip the black wire (which is in the shape of a C) under a metal bolt or screw in your vehicle (this is the ground wire). Check that it is not attached to plastic parts. You will typically need a socket wrench to loosen the nut or bolt that you choose to ground with. To attach the grounding terminal, loosen the nut or bolt enough to slip it in and tighten it back up afterward
What's in the box
Mini USB Dash Cam Hardwire Kit
Mini/LP ACN Add-A-Circuit Fuse Holder
Mini ACS Add-A-Circuit Fuse Holder
ATO ACU Add-A-Circuit Fuse Holder

Country USA
Brand VMVM
Manufacturer VMVM
Binding Electronics
ItemPartNumber hardwire-kit
Size micro-port
UPCs 788601805421
EANs 0788601805421
ReleaseDate 0000-00-00

Country	USA
Brand	VMVM
Manufacturer	VMVM
Binding	Electronics
ItemPartNumber	hardwire-kit
Size	micro-port
UPCs	788601805421
EANs	0788601805421
ReleaseDate	0000-00-00

Dash Cam Hardwire Kit Micro USB 10ft 12V-24V to 5V, Low Voltage Protection Mini/ACS/ATO Add a Circuit Fuse Holders Compatible Dash Cam, GPS, Radar Detector All Other Micro USB Device

You might also like...