SPIGHTDEX LED Strip Light Dimmer DC 5V-24V 10A PWM Wireless RF

SPIGHTDEX LED Strip Light Dimmer DC 5V-24V 10A PWM Wireless RF Remote Control Full Protection for Wrong Wiring Output Short Circuit Overload Overheat for Single Color LED Strip Tape 2835 3528
- Note 1:When the controller is normally powered on, the indicator light of the controller(receiver) will be green. If the indicator light is not on, it will prove that the controller is not installed correctly and is not normally powered on. Check whether the input and output are connected backwards, whether the screw is tightened and the line is in normal contact, and whether the line corresponds to the positive and negative poles of the controller.
- Note 2:The voltage of the power supply should correspond to the voltage of the led strip light. For example, if the lamp belt is DC12V, the dc power supply of DC12V should be connected. If a 24V lamp is connected to a 12V power supply, it will not light up.
- Note 3:The Driver be connected to the input positive and negative poles of Dimmer. Then output of Dimmer be connected to led strip. Positive and negative poles be corresponding. If the power is connected to the output end of the dimmer and the light is connected to the input end of the dimmer, the strip will always be on but not under control. Press the remote, the receiver indicator will flash indicate to that the command of the remote control has been accepted, but the light is out of control.
- Note 4：The factory state of the controller remote control is 1-to-1 pairing. If the remote control is out of order, there will be a mismatch between the remote control and the controller, so it needs to be repaired. Refer to the instructions for matching
- Note 5:The SP-N12 LED DIMMER is a constant voltage controller and can only be connected to a constant voltage lamp. It is not suitable for constant current lamps. The controller indicator light appears red, indicating a short circuit. The controller indicator light appears yellow, indicating overload.So Please check clear with your lighting before you purchase our LED Dimmer. Please contact us if you have any questions for it. we will get back to you asap in 12 hours.
SP-N12-11A single color LED dimmer is designed to drive constant voltage LED products in voltage range of DC5-24V.
The main unit works with a RF remote controller, user can adjust LED brightness on the remote controller. The main unit is powered by DC power supply and receives remote controller commands to drive LED fixtures.

Specification
Model:SP-N12-10A
Brightness grade: 11 levels
PWM grade: 4000 steps
Overload protection:Yes
Overheat protection: Yes
Working voltage: DC 5-24V
Remote frequency: 433.92MHz
Remote control distance: >15m at open area
Rated output current:1x11A
Controller dimension:87x24x15mm

Work status indicator: (This indicator displays all working status of the controller) It shows different events as following:
Steady green: Normal working.
Single green blink: Command received.
Long single green blink: Mode or color cycle edge.
Long single yellow blink: Reach brightness limit.
Red flash: Overload protection.
Yellow flash: Over heat protection.
Green flash 3 times: New remote controller paired.

Brightness control:
Press the upward key to increase brightness and press the downward key to decrease. The brightness will change smoothly when hold pressing these two keys.
The controller applies brightness gamma correction on dimming control, makes the brightness tuning more smooth to human sense.

Package included:
1 x RF remote control
1 x receiver(CR2032 button battery)
1 x screw-driver
1 x instructions.

Country	USA
Brand	SPIGHTDEX
Manufacturer	SPIGHTDEX
Binding	Unknown Binding
ItemPartNumber	SP-N12-11A
Model	SP-N12-11A
Color	Single Color
Size	SP-N12-11A
UnitCount	1
UPCs	667322258818
EANs	0667322258818
ReleaseDate	0000-00-00

SPIGHTDEX LED Strip Light Dimmer DC 5V-24V 10A PWM Wireless RF Remote Control Full Protection for Wrong Wiring Output Short Circuit Overload Overheat for Single Color LED Strip Tape 2835 3528

You might also like...