Hymnorq Titanium Coated High Speed Steel 6542 (M2) Metric 1/4"

Hymnorq Titanium Coated High Speed Steel 6542 (M2) Metric 1/4" Hex Shank Spiral Flute 2-in1 Combination Drill and Tap Bit M3-M10 Set of 6pcs for Tapping Aluminum Plate Wood Copper Plate Iron Plate
- This set of drill tap bits are made of HSS 6542(M2), which is much harder than the silver HSS 4341 bits and not easy to break. Suitable for drilling and tapping in aluminum plate, wood, copper plate, plastic, iron plate
- Combine drill and tap in a single pass to save your labor and precious time
- Self-centering point eliminates the need for center drilling or center punching
- Wide flutes carry the chips out of the hole. Can be used on multi-spindle heads with reversing mechanisms for tapping in most materials
- 6 sizes in one drill and tap bit set (M3, M4, M5, M6, M8, M10) to meet your diversified requirements; Quick change 1/4" (6.35mm) hex shank with Metric sizes engraved on the bits
Overview
This set of drill tap bits are made of High Speed Steel 6542 (HSS M2). It's a tungsten-molybdenum high speed steel with a well-balanced composition suitable for a wide variety of applications. Because of its superior properties and relative economy, this set of drill tap bits is a better choice than the lower-priced silver HSS 4341 drill tap bits, if you're mainly tapping on metals.

These Migiwata drill taps are a great time saving accessory. Each one is a combination of a twist drill bit and a tap. The point is the same as a twist drill bit, which is self-centering. So you don't have to buy a centering drill bit or a center punch.Now you can drill and tap at the same time in one operation. Just drill until the drill section fully enters the material, then the tapping will start to occur.

When it reaches the right depth, reverse the drill to deburr and remove any swarf to complete the job. No tool changes, good alignment and fast cycle times make this a very productive tool.

The Migiwata tap drill set also features wide spiral flute, which allow the chips to easily get out of the hole, preventing chip crowding and breakage of tap drill bits.

NOTICE:
It's highly recommended that the combination drill and tap bits are used on a tapping machine.
If you apply an electric hand drilling machine to do the tapping job, please pay attention to your operating, because excessive shaking and tilting may affect the result and even break the bit.

Specification:
Material: HSS 6542(M2)
Coating: Titanium
Shank: 1/4" (6.35mm) hex shank
Color: Golden
Tapping Material: Aluminum Plate, Wood, Copper Plate, Plastic, Iron Plate

What you'll get:
M3x0.5 Drill Tap Bit x 1pc
M4x0.7 Drill Tap Bit x 1pc
M5x0.8 Drill Tap Bit x 1pc
M6x1 Drill Tap Bit x1pc
M8x1.25 Drill Tap Bit x 1pc
M10x1.5 Drill Tap Bit x 1pc
Country USA
Brand HYMNORQ
Manufacturer Hymnorq
Binding Tools & Hardware
ItemPartNumber DB013
Color Gold Metric
Size Small
UnitCount 6
UPCs 712492806427
EANs 0712492806427
ReleaseDate 0000-00-00

Country	USA
Brand	HYMNORQ
Manufacturer	Hymnorq
Binding	Tools & Hardware
ItemPartNumber	DB013
Color	Gold Metric
Size	Small
UnitCount	6
UPCs	712492806427
EANs	0712492806427
ReleaseDate	0000-00-00

Hymnorq Titanium Coated High Speed Steel 6542 (M2) Metric 1/4" Hex Shank Spiral Flute 2-in1 Combination Drill and Tap Bit M3-M10 Set of 6pcs for Tapping Aluminum Plate Wood Copper Plate Iron Plate

Customers who purchased this also purchased....