Pivit Oxygen Tubing Y-Connector | Fits 3/16in and 1/4in ID

Pivit Oxygen Tubing Y-Connector | Fits 3/16in and 1/4in ID Tubing | Barbed Ends For Secure Leak-Free Connections | Connects 2 Oxygen Sources For Higher Flows | Mobility Without Pulling On Your Cannula
- ✅ VERSATILE INTERNAL DIAMETER FITS MOST OXYGEN TUBING - These durable Y-connectors will fit any standard oxygen tubing that is 3/16in or 1/4in. All of the male prongs are the same size to allow for a universal connection.
- ✅ LIGHTWEIGHT CONNECTORS WITH BARBED ENDS FOR A SNUG FIT - These connectors are made lightweight to ensure that the tubing of the users is not weighted down. Each male prong is equipped with barbs to prevent the tubing from coming off of the connector accidentally. Though they are barbed for a snug fit, the low angle of the connection slope allows for the tubing to be removed relatively easily.
- ✅ PIVIT Y-CONNECTORS ARE SHATTERPROOF - ard plastic connectors can crack or even shatter when pulled or pushed on with too much weight causing a serious problem for the user. Pivit Y-connectors are shatterproof to provide the user with a long-lasting product for extensive usage.
- ✅ EASY TO CONNECT AND DISCONNECT - Simple to use while switching out your tubing. Many connectors with steep tapered fittings get stuck in the tubing, causing a struggle to ensue for the simple act of replacing or moving tubes. Some people simply cannot get the tubing off and end up cutting the tubing off of the connector, but we're here to ensure that this does not happen to you.
- ✅ CONNECTS TWO OXYGEN SOURCES TO RAISE OR SPLIT FLOWS - These connectors allow the patient to connect two oxygen sources with a lower flow together to produce a higher concentration of oxygen to the patient. For example, if you have two sources of oxygen running 7.5 liters, you can connect them with this piece and produce 15 liters. They can also be used to split one oxygen source between two patients if both users require 2 liters of oxygen, the oxygen would have to be running at 4 liters.
Allows for connecting two oxygen sources together or splitting one oxygen source between two people

The Pivit Y-connector allows for two oxygen sources producing smaller amounts of oxygen per minute to be combined to provide more oxygen. It can also be used when two people use oxygen therapy daily by splitting the oxygen from a single source between them. If you are splitting the oxygen between two patients, it is important to know that you are cutting the liters per minute in half for each patient. Therefore, if both patients need 2LPM you would have to run the oxygen source at 4LPM to provide sufficient oxygen.

Lightweight construction with a universal and snug fit for almost any oxygen tubing

This connector is able to be used in conjunction with all standard 3/16" and 1/4" oxygen tubing on any of the three equally sized prongs. Each prong is barbed and tapered at a low angle to provide a sturdy fit for the tubing which can still be easily removed with a pull-and-twist motion. They are lightweight and durable to prevent unwanted weight on the tubing as well as shattering and cracking which are common with similar products made from hardened plastic.Â

Allows for the user or caregiver to see obstructions within the connector when they occur

Obstructions in oxygen therapy can cause the user to recieve insufficient oxygen. When an obstruction occurs, it may go unnoticed until the negative signs of low oxygen start to show in the user. The best way to prevent an obstruction from going unchecked is to make sure that it can be checked with a simple glance. Lack of necessary oxygen can lead to hypoxia and hypomexia which may cause:
- Changes in skin color
- Wheezing and coughing
- Elevated heart rate
- Hyperventilation
- Shortness of breath
- Confusion
- Sweating
- Organ Failure

Country	USA
Binding	Health and Beauty
Brand	pivit
Color	White
Department	unisex-adult
EAN	0603051185629
IsAdultProduct	0
Label	waymo
Manufacturer	waymo
MPN	PYND50519H
NumberOfItems	1
PartNumber	PYND50519H
Publisher	waymo
Size	3/16in and 1/4in ID Tubing
Studio	waymo
ReleaseDate	0000-00-00

Pivit Oxygen Tubing Y-Connector | Fits 3/16in and 1/4in ID Tubing | Barbed Ends For Secure Leak-Free Connections | Connects 2 Oxygen Sources For Higher Flows | Mobility Without Pulling On Your Cannula

You might also like...