Seamax EZ Load Boat Launching Wheels Set for Inflatable Boat &

Seamax EZ Load Boat Launching Wheels Set for Inflatable Boat & Aluminum Boat, Support MAX 500Lbs Loading with 12" Pneumatic Tire & 2 Height Position
- Seamax Easy Load Boat Launching Wheels Set is designed by Seamax Canada, made by hardest marine grade T6 aluminum alloy with CNC processing; Shiny looking anodized coating on all aluminum parts, product is good for saltwater using; Small parts are all made by solid stainless steel. Lab 1000Lbs tested, support MAX 500Lbs loading in all condition, good for inflatable boats, aluminum boats and fiberglass boats.
- This system is designed for boats with transom, the length of the boat should not exceed16 FT & total weight within 500 Lbs. These transom wheels should only be installed by an adult with some experience in working with tools. To install the wheel set properly, you will need to drill 4 holes (5/16”) in the transom for the mounting. Addition reinforcement may be required on some aluminum transom. And you can use marine sealant and suggested Sikaflex 291.
- Benefit from its new Push Button design & max 3 stages wheel arm, the system can be adjusted while afloat in the boat leaving or coming into, it can also bring different performance position for boat launching. The wheel arm length increment is 2.5” per stage, plus the wheel’s diameter, the range of length is 22-28 inches.
- Tire inflation: Dolly tires may not be fully inflated when shipping; please only give 15-20 PSI pressure at room temperature before using. Best to use portable type digital air pump in case tire over inflated. Tire over inflated will cause damage and the warranty is not covered. Dual wheel kit is available for this dolly for heavy loading application.
- Maintenance: Wash it after using from salt water or sandy beach. Check tire pressure before every using. Don’t store the wheels under the sun or beside the heat to maximize its life time. Take the wheel arm off from the transom bracket when store your boat. Lube the spring load dolly system is necessary. Keep the lock pin on the dolly bracket. Manufacturer 2 years Parts Limited Warranty within USA & Canada. 30 days free replacement on any defective ransom wheel sets.
Instructions
1). These wheels have 2+1 adjustment positions for length base on the wheel arm end rotation position upper or lower. to remove the leg assembly from the bracket, simply push the stainless steel locking button and then the rotation button to release.
2). The wheels must face towards the boat tubes and be as far apart as possible (this will give you more stability when moving the boat around) and clear the boat tubes by about one inch so they don't rub against the tubes when being raised or lowered. the wheels must also clear the bottom of the boat by about one inch when placed in their lowered position.
3). Once you have determined the mounting positions for the brackets which should be straight up and down on the transom and about 6-8 inches up from the bottom of the bracket to the bottom of the boat, mark where to drill the 5/16" holes (drill bit not included). This is best done by separating the leg assembly from the bracket. double check everything again before drilling any holes! holes and transom must be vertical.
4. Use the supplied washers and lock nuts on the bolts on the inside of the transom to secure the brackets to the transom and then cap them with the supplied acorn nuts to protect your boat when rolled up.
www.seamaxcanada.com 1877-907-7766
Country USA
Brand Seamax
Manufacturer Seamax Marine
Binding Apparel
ItemPartNumber EZ-Load
UPCs 081175857019
EANs 0081175857019
ReleaseDate 0000-00-00

Country	USA
Brand	Seamax
Manufacturer	Seamax Marine
Binding	Apparel
ItemPartNumber	EZ-Load
UPCs	081175857019
EANs	0081175857019
ReleaseDate	0000-00-00

Seamax EZ Load Boat Launching Wheels Set for Inflatable Boat & Aluminum Boat, Support MAX 500Lbs Loading with 12" Pneumatic Tire & 2 Height Position

You might also like...