SENSKY BS010WL DC 12v to 24v Mini Pir Motion Sensor Switch

Description Specifications
Description
SENSKY BS010WL DC 12v to 24v Mini Pir Motion Sensor Switch Occupancy Sensor Switch for DIY LED Lighting (Light Sensor, Delay Time, Sensor Distance, Adjustable)
- 【Motion Activated】 : Sensor function triggered by motion, you can use this small motion sensor switch to control lighting like Led strip lighting.
- 【Light Sensor Adjustable】: This function allows you to use the motion sensor in different ambient condition, for example, you set the light sensor value to 20 lux, when the room ambient light value is above 20 lux, the light won’t turn on, but when room ambient light value is less than 20 lux, the sensor can turn light on when motion detected within sensing range.
- 【Delay Time Adjustable- Please set this to its minimum value first then try to figure out your values for the Sensitivity and Light Sensor- this will save your time】: The delay time controls how long the light stays on once it gets triggered, during the delay time if motion detected, the delay time will reset and start a new delay time.
- 【Sensitivity Adjustable】: The sensitivity controls how close you need to be to the sensor in order to activate it.
- 【Wide Application】: You can use this sensor in different occasions like entryway lighting, cabinet lighting,lighting, pantry lighting, under the bed rails lighting.
Sensky BS010WL Dc 12v 24v 3a Mini Pir Motion Sensor Switch,occupancy Sensor Switch for DIY LED Lighting

Description:
PIR(Passive infrared) Motion sensor is pyroelectric device can detect human movement by detecting Infrared ray emitted by human body.
Automatic Induction: When people enter into the range of induction, it will output a voltage equal to input voltage, after the delay time, it will output 0V; during the delay time if motion detected, the delay time will reset, and start a new delay time.
widely used on the Motion-activated lighting, LED strips Security System, automatic sensory device and more.

Specifications :
Operating voltageÃ¯Å¡DC12V
Load currentÃ¯Å¡3A
Delay timeÃ¯Ë†Default settingÃ¯â€°Ã¯Å¡5-25s (2~280 Seconds adjustable)
Detecting range : About 110 degrees cone angle
Detecting distance: 4M-7M (10cm-7M adjustable)
Trigger way : continuous triggering
Blockade time: 0 seconds
size: 48*25*14 mm
Attention:
1.Don't exposed to direct sun light or lighting, big wind, near a heater or air condition.
2.Don't fix it at a place where there are obstructing material (e.g. Glass, dense clothes) which IR cannot get though.
3.Don't fix it in strong shock or vibration environment.
4.The PIR Sensor requires a 'warm-up' time in order to function properly, about 10s to1min,depend on the delay time; during this time, the signal triggered by the module is not stable, after one minute, it will be ready.
Specifications
Country USA
Brand Sensky
Manufacturer SENSKY
Binding Tools & Home Improvement
ItemPartNumber GKG0103W0000L
Model BS010WL
Color White
UPCs 700646315260
EANs 0700646315260
ReleaseDate 0000-00-00

Country	USA
Brand	Sensky
Manufacturer	SENSKY
Binding	Tools & Home Improvement
ItemPartNumber	GKG0103W0000L
Model	BS010WL
Color	White
UPCs	700646315260
EANs	0700646315260
ReleaseDate	0000-00-00

SENSKY BS010WL DC 12v to 24v Mini Pir Motion Sensor Switch Occupancy Sensor Switch for DIY LED Lighting (Light Sensor, Delay Time, Sensor Distance, Adjustable)

You might also like...