Weller WES51 Compatible Heat-Set Insert Installation tip for

Weller WES51 Compatible Heat-Set Insert Installation tip for #4-40 and M5 Inserts Compatible with Weller WES51 Irons and Weller ET-Series Tips. Used for Connecting 3D Printed Parts.
- Longer shank than other tips allows you to reach deeper into 3D printed parts and tight corners to install heat-set inserts without touching your iron and melting the plastic
- Installation tip works better than soldering iron tip since conical tips can catch on the insert and accidentally pull the insert out while melting the plastic and ruining the part.
- One tip works for #4-40 and M3 and the other tip works for M5 inserts for same price as other's single tip. More types of inserts and better reach than other installation tips. #4/M3 tip works okay for #6 and M4 inserts, but just not a perfect fit...still better than a soldering iron.
- Tips are compatible with Weller irons like WES51, WESD51, or any iron that can use a Weller ET-Series tip. Other tips are not at all compatible with WES51, Hakko, or any iron that used ET-Series tips. We have not tested every possible soldering iron. If you have a Hakko iron or if you have an iron with a 1/4" barrel, search ASIN instead: B078K72615
- If you need some brass inserts to get going, search Amazon for ASIN: B07BH5X252 for a bag of 50 insert nuts. Install tips are made in the USA. Not intended to be used for soldering. Soldering iron not included.
Heat set inserts are a great way to improve connection strength between 3D printed parts. However, if you have tried to set heat-set inserts in your plastic or 3D printed part with your soldering iron, you may have had the frustration of pushing the insert in only to have it come right back out stuck to your soldering iron and ruining your part in the process. Most soldering iron tips can catch on the rim of the insert causing it to stick on the iron when you pull the iron out. If you use the "horizontal method" it's hard to know the insert is straight and it's easy to put it in crooked. Our insert tips have a vertical wall that solves that problem. The iron pulls right out after pressing the hot insert. Because the shoulder is square it's easier to know if the insert is square in the piece, something that's harder to control with a conical soldering tip. The shank is much longer (0.75") and narrower than what you get with other insert tips (only 0.25" long), allowing you to set small inserts into corners of parts without melting the side of the part. This is especially useful if you're mounting a circuit board in a 3D printed box or doing a mounting that requires the insert to come close to the edge of the part. Compatibility with Weller WES51/WESD51 irons, or any iron that takes the Weller ET Series tips, will let you use the iron you already own. Two tips included, one for #4-40 and M3 and the other for M5 inserts. *** Has not been tested with every possible soldering iron. Not all Wellers irons use ET Series tips. Weller produces many series of tips. This one is compatible with ET-Series. Soldering iron not included.***
Country USA
Brand Virtjoule
Manufacturer Virtjoule
Binding Misc.
ItemPartNumber Heatset4-40M5Weller
Color Brass
Size #4-40, M5
UPCs 040232289651
EANs 0040232289651
ReleaseDate 0000-00-00

Country	USA
Brand	Virtjoule
Manufacturer	Virtjoule
Binding	Misc.
ItemPartNumber	Heatset4-40M5Weller
Color	Brass
Size	#4-40, M5
UPCs	040232289651
EANs	0040232289651
ReleaseDate	0000-00-00

Weller WES51 Compatible Heat-Set Insert Installation tip for #4-40 and M5 Inserts Compatible with Weller WES51 Irons and Weller ET-Series Tips. Used for Connecting 3D Printed Parts.

You might also like...